PSC MAGELLAN 1000I Manuel d'instructions Page 63
- Page / 160
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Product Reference Guide
4-1
Chapter 4
Data Editing
Data Editing Overview
When a bar code is scanned, additional information can be sent to the host computer along
with the bar code data. This combination of bar code data and supplementary user-defined
data is called a “message string.” The features in this chapter can be used to build specific
user-defined data into a message string.
There are several types of selectable data characters that can be sent before and after scanned
data. You can specify if they should be sent with all symbologies, or only with specific symbolo-
gies.
Figure 4-1 shows the available elements you can add to a message string:
Figure 4-1. Breakdown of a Message String
Please Keep In Mind...
• Modifying a message string is not a mandatory requirement. Data editing is sophisticated
feature allowing highly customizable output for advanced users. Factory default settings
for data editing is typically set to NONE.
• A prefix or suffix may be applied (reference the
Symbologies chapter for these settings)
across all symbologies (set via the Global features in this chapter).
• You can add any character from the ASCII Chart (from 00-FF) on the inside back cover of
this manual as a prefix, suffix or Label ID.
CAUTION
It is not recommended to use these features with IBM
or Wand Emulation interfaces.
Prefix SuffixAIM IDLabel ID Label IDBar Code Data
00 - 20 Characters (ASCII)
Label ID Transmission:
Enable this option to
transmit the Label ID you
configure for the scanned
symbology.
AIM ID: This function is used to identify and display the
common label identifier for its symbology. When enabled,
this ID code will be transmitted before the scanned bar
code data.
OR...
- Magellan 1
- Table of Contents 3
- Product Reference Guide 5
- Getting Started 7
- Connecting the Scanner 8
- Programming 9
- LED and Beeper Indicators 10
- Error Codes 11
- 1-6 Magellan 12
- General Features 13
- Double Read Timeout — cont 14
- Label Gone Timeout 15
- Sleep Mode 16
- Sleep Mode — cont 17
- Good Read: When to Indicate 19
- ³ 001402 20
- Good Read Beep Length 21
- Good Read Beep Volume 22
- Targeted Scanning Mode 23
- Target Mode Linger Time 24
- Wake Up Intensity 25
- Wake Up Intensity — cont 26
- Interface Related Features 27
- Interface Selection 29
- ³ 000132 30
- ³ 00013B 31
- Interface Selection — cont 32
- Obey/Ignore Host Commands 33
- Host Transmission Buffers 34
- RS-232 Interface Features 35
- Hardware Flow Control 37
- Intercharacter Delay 38
- Intercharacter Delay — cont 39
- Software Flow Control 39
- Host Echo 40
- Host Echo Quiet Interval 41
- Signal Voltage: Normal/TTL 42
- RS-232 Invert 43
- Beep on ASCII BEL 43
- Beep on Not on File 44
- ACK NAK Options 45
- ACK Character 46
- NAK Character 46
- Retry on ACK NAK Timeout 47
- ACK NAK Timeout Value 47
- ACK NAK Retry Count 48
- ACK NAK Error Handling 49
- IBM-USB Device usage 50
- Interface Features 51
- Supported Symbologies 52
- Bar/Space Polarity 53
- Wand Idle State 53
- Signal Speed 54
- Transmit Trailing Noise 54
- Transmit Leading Noise 55
- Symbology Conversion 55
- USB Keyboard 56
- Keyboard Wedge — cont 57
- Caps Lock State 58
- Data Editing 63
- 00 - 20 Characters (ASCII) 64
- Global Prefix/Suffix — cont 65
- Label ID 67
- Label ID — cont 68
- Case Conversion 73
- Character Conversion 74
- UPC-A — continued 76
- Disable/Enable UPC-E 79
- Check Digit Transmission 79
- UPC-E — continued 80
- Expand UPC/EAN to GTIN 82
- Disable/Enable EAN-13 83
- EAN-13 — continued 84
- Disable/Enable EAN-8 86
- EAN-8 — continued 87
- Enable EAN Two-Label 88
- Contact Customer Support for 89
- Add-ons — continued 90
- Disable/Enable RSS-14 91
- UCC/EAN 128 Emulation 91
- RSS-14 — continued 92
- RSS Expanded 93
- RSS Expanded — continued 94
- Disable/Enable Code 39 97
- Check Character Calculation 97
- Start/Stop Characters 98
- Code 39 Full ASCII 99
- Code 39 — continued 100
- Quiet Zones 101
- Pharmacode 39 103
- Check Character Transmit 104
- Code 128 105
- Code 128 — continued 106
- Interleaved 2 of 5 109
- Check Digit Transmit 110
- Length Control 111
- Symbologies 112
- Interleaved 2 of 5 Stitching 113
- Minimum Reads 114
- Disable/Enable Codabar 115
- Check Character Verification 115
- Codabar — continued 117
- Start/Stop Character Match 120
- Codabar Stitching 120
- Disable/Enable Code 93 122
- Code 93 — continued 123
- MSI/Plessey 126
- MSI/Plessey — continued 127
- Standard 2 of 5 132
- Standard 2 of 5 — continued 133
- 5-64 Magellan 138
- Appendix A 139
- Product Specifications 139
- Physical Properties 140
- Electrical Parameters 140
- Environmental Parameters 140
- Other Parameters 140
- Cable Pinouts 141
- USB & USB Keyboard 142
- Wand Emulation 142
- Keyboard Wedge 142
- Alpha-Numeric Pad 143
- Default Settings 145
- IBM Interfaces 146
- RS-232 Wincor/Nixdorf 146
- Keyboards 147
- D-4 Magellan 148
- Keyboard Function Key 149
- Mappings 149
- Host Commands 155
- F-2 Magellan 156
- Sample Symbols 157
- ASCII Chart 159
Produits connexes et manuels pour Lecteurs de codes-barres PSC MAGELLAN 1000I
(116 pages)
Lecteurs de codes-barres PSC DUET Spécifications
(400 pages)
(400 pages)
(48 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.964 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels