PSC SP400rf Manuel d'utilisateur Page 102
- Page / 112
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
APPENDIX
A
S
TD. D
EFAULTS
96
SP400RF
Programming Guide
APPENDIX A
STANDARD FACTORY SETTINGS
FACTORY DEFAULTS
Text formatted in BOLD type indicates the standard factory configuration
setting. These settings are valid if these settings have not been changed
in a previous programming session.
SYMBOLOGY SELECTION
UPC/EAN
Symbology-------------------------------ENABLE Disable
Expand UPC-A to EAN-13 -------------Enable DISABLE
Expand UPC-E to UPC-A --------------Enable DISABLE
Expand EAN-8 to EAN-13 -------------Enable DISABLE
Expand UPC-E to EAN-13 -------------Enable DISABLE
Add-Ons ----------------------------------Required Optional DISABLE
Price/Weight Check --------------------DISABLE 4-Digit 5-Digit
Euro 4-Digit Euro 5-Digit
CODE 39
Symbology-------------------------------Enable DISABLE
Check Digit ------------------------------Calculate DON'T CALCULATE
Check Digit ------------------------------SEND Don't Send
Start/Stop Character -------------------Send DON'T SEND
Read One Character Label ------------Enable DISABLE
Code 39 Minimum Label Length ----1
Code 39 Full ASCII ---------------------Enable DISABLE
INTERLEAVED 2 OF 5
Symbology-------------------------------ENABLE Disable
Check Digit ------------------------------Calculate DON'T CALCULATE
Check Digit ------------------------------SEND Don't Send
Label Format ----------------------------Fixed VARIABLE LENGTH
Set 1st Fixed Length -------------------14
Set 2nd Fixed Length ------------------8
Minimum Length -----------------------2
- REQUENCY 1
- PSC Scanning, Inc 2
- Contents 3
- Symbologies 4
- Appendix A 5
- Appendix B 5
- Appendix C 5
- INTRODUCTION 7
- CHANGING INTERFACES 8
- INFORMATION 9
- PROGRAMMING OVERVIEW 10
- THE PROGRAMMING SESSION 11
- IF YOU MAKE A MISTAKE 12
- RETURN TO FACTORY SETTINGS 12
- CONFIGURATION UPLOAD 12
- WHERE TO GO FROM HERE 13
- ORT 5B INTERFACE SELECTION 14
- ORT 9A, 9B, 9C, 9E SETTINGS 15
- ORT E INTERFACE SELECTION 16
- OCIA INTERFACE SELECTION 17
- SNI OCIA INTERFACE SELECTION 17
- OCIA OPTIONS 18
- R44-1027 13 19
- WAND EMULATION 19
- INTERFACE 19
- MULATION 20
- NTERFACE 20
- RS-232 INTERFACE SELECTION 21
- AUD RATE 22
- R44-1027 17 23
- HARDWARE CONTROL 24
- SOFTWARE CONTROL 25
- MILLISECONDS 27
- NTERCHARACTER 27
- I/F Type PCs Supported 28
- R44-1027 25 31
- IMPORTANT 32
- IBMXXXX STI WEDGE 32
- PREFIX & SUFFIX 33
- ABEL TRANSMIT 35
- ORMAT CONFIG 35
- ET SUFFIX 36
- NE CHARACTER ONLY 38
- ASCII CHARACTER SET 39
- ONTINUED 41
- R44-1027 37 43
- R44-1027 39 45
- SYMBOLOGIES 47
- SYMBOLOGY OPTIONS OVERVIEW 48
- SYMBOLOGY SELECTION 49
- UPC/EAN OPTIONS 51
- UPC/EAN EXPANSION 52
- UPC/EAN ADD-ONS 53
- END CHECK DIGIT 55
- PRICE/WEIGHT CHECK DIGIT 56
- CODE 39 OPTIONS 57
- CODE 39 (CONTINUED) 58
- ODE 39 MINIMUM 60
- ABEL LENGTH 60
- INTERLEAVED 2 OF 5 61
- YMBOLOGY 62
- ELECTION 62
- ET FIXED 63
- ETTING FIXED LENGTHS 63
- ETTING MINIMUM LABEL LENGTH 63
- R44-1027 59 65
- STANDARD 2 OF 5 66
- ORMAL STANDARD 2 OF 5 67
- TANDARD 2 OF 5 67
- ET FIRST FIXED LENGTH 69
- CODABAR OPTIONS 71
- Start/Stop 73
- Standard Factory Settings 73
- CODABAR FIXED LENGTH 74
- R44-1027 69 75
- MSI/PLESSEY CHECK DIGIT 76
- NABLE MSI/PLESSEY FIXED 77
- ISABLE MSI/PLESSEY FIXED 77
- NABLE FIXED L 77
- ET SECOND FIXED LENGTH 78
- O SECOND FIXED LENGTH 78
- LESSEY SET FIXED 78
- NABLE 79
- YMBOLOGY ID PREFIX 79
- GENERAL FEATURES 80
- COMMUNICATIONS PROTOCOL 81
- FEATURES 83
- ET STX 85
- ET ETX 85
- ET STX/ETX 85
- "When to Beep" 86
- CTS enabled 88
- R44-1027 83 89
- “WHEN TO BEEP” OPTIONS 90
- R44-1027 87 93
- BEEPER VOLUME 94
- RADIO CHANNEL FREQUENCY 95
- Radio Channel Frequency 96
- AIT TIME FOR HOST ACKNOWLEDGE 97
- IME FOR HOST 98
- CKNOWLEDGE 98
- READ VERIFICATION 99
- Programming Guide 100
- LOW BATTERY INDICATION METHOD 101
- APPENDIX A 102
- STANDARD FACTORY SETTINGS 102
- TANDARD 2 OF 5 103
- ISC. GENERAL FEATURES 104
- EAD VERIFICATION 104
- TEM ON/OFF FILE 104
- UDIBLE INDICATOR SETTINGS 104
- INTERFACE-DISCRETE DEFAULTS 105
- IBM INTERFACES 106
- APPENDIX B 107
- ADDITIONAL INFORMATION 107
- APPENDIX C 108
- SAMPLE BARCODES 108
- 1 101234 567891 109
- LANK PAGE 111
- Corporate Headquarters 112
Produits connexes et manuels pour Lecteurs de codes-barres PSC SP400rf
(104 pages)
(48 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.043 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels