PSC LINEAR IMAGER 7000 Manuel d'instructions Page 52
- Page / 212
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Interface Related Features
3-24 PowerScan
®
7000 Linear Imager
RS-232 Interface Features — cont.
ACK Character
START
MODE BARCODE
Sets the ACK character from the set of ASCII charac-
ters or any decimal value from 000 to 255. Pad
entries of less than three digits with zeros, as in
“005”. To configure this feature, scan the “START” bar
code above to place the unit in Programming Mode,
then the “Set ACK Character,” followed by the digits
from the Alphanumeric table in
Appendix C, Alpha-
Numeric Pad
representing your desired character.
Exit programming mode by scanning the “END” bar-
code below.
DEFAULT SETTING FOR THIS FEATURE: 006
Set ACK
Character
END
- PowerScan 1
- Linear Imager 1
- Table of Contents 3
- Product Reference Guide iii 5
- Getting Started 7
- Connecting the Scanner 8
- Reference 9
- Defaults 10
- General Features 11
- 2-2 PowerScan 12
- Powerdown Timeout 13
- Powerdown Timeout — continued 14
- LED and Beeper Indicators 15
- Good Read: When to Indicate 16
- Good Read Beep Control 17
- Good Read Beep Frequency 18
- Good Read Beep Length 19
- 2-10 PowerScan 20
- Good Read Beep Volume 21
- Scanning Features 22
- Scan Mode — continued 23
- Active Scanning Time 24
- Laser Pointer Control 26
- 2-18 PowerScan 28
- Interface Related 29
- Features 29
- Interface Selection 32
- Interface Selection — cont 33
- Interface Features 36
- Global Interface Features 37
- RS-232 Interface Features 38
- 3-12 PowerScan 40
- Hardware Flow Control 42
- Intercharacter Delay 42
- Software Flow Control 42
- 3-16 PowerScan 44
- Host Echo 46
- Host Echo Quiet Interval 46
- Signal Voltage: Normal/TTL 46
- RS-232 Invert 46
- 3-20 PowerScan 48
- Beep on ASCII BEL 49
- Beep on Not on File 49
- ACK NAK Options 50
- ACK NAK Options — cont 51
- ACK Character 52
- NAK Character 53
- Retry on ACK NAK Timeout 54
- ACK NAK Timeout Value 55
- ACK NAK Retry Count 56
- ACK NAK Error Handling 57
- 3-30 PowerScan 58
- IBM-USB Interface Features 59
- 3-32 PowerScan 60
- Wand Emulation — cont 62
- Symbology Conversion 66
- Symbology Conversion — cont 67
- Keyboard Wedge/USB Keyboard 68
- 3-42 PowerScan 70
- 3-44 PowerScan 72
- 3-46 PowerScan 74
- Set Wedge Quiet Interval 75
- 3-48 PowerScan 76
- Appendix C, Alpha 76
- Numeric Pad 76
- Data Editing 77
- Global Prefix/Suffix 78
- Appendix C 79
- 4-4 PowerScan 80
- Appendix C, Alpha-Numeric 80
- AIM ID — continued 82
- Label ID 83
- Label ID — continued 84
- Case Conversion 90
- Character Conversion 91
- 4-16 PowerScan 92
- Disable/Enable UPC-A 94
- Expand UPC-A to EAN-13 94
- System Number Transmission 94
- UPC-A — continued 95
- Disable/Enable UPC-E 100
- Check Digit Transmission 100
- System Number 100
- Expand to UPC-E to UPC-A 100
- Expand UPC-E to EAN13 100
- UPC-E — continued 101
- Disable/Enable GTIN 104
- Disable/Enable EAN-13 105
- EAN-13 Flag 1 Character 105
- EAN-13 — continued 106
- Disable/Enable EAN-8 109
- EAN-8 — continued 110
- 5-20 PowerScan 112
- 7000 Linear Imager 112
- Add-ons — continued 113
- Disable/Enable RSS-14 114
- UCC/EAN 128 Emulation 114
- RSS-14 — continued 115
- RSS Expanded 117
- RSS Expanded — continued 118
- Disable/Enable Code 39 122
- Check Character Calculation 122
- Check Character Transmit 122
- Start/Stop Characters 122
- Code 39 Full ASCII 122
- Code 39 — continued 123
- Instructions 127
- Pharmacode 39 131
- Pharmacode 39 — continued 132
- Code 128 133
- Code 128 — continued 134
- Interleaved 2 of 5 140
- Length Control 142
- 5-52 PowerScan 144
- Interleaved 2 of 5 Stitching 145
- Minimum Reads 146
- Disable/Enable Codabar 147
- Check Character Verification 147
- Codabar — continued 148
- Disable/Enable Code 93 158
- Code 93 — continued 159
- MSI/Plessey 164
- MSI/Plessey — continued 165
- Standard 2 of 5 172
- Standard 2 of 5 — continued 173
- Disable/Enable PDF 417 179
- PDF 417 — continued 180
- Symbologies 184
- Appendix A 185
- Product Specifications 185
- Physical Properties 186
- Electrical Parameters 186
- Environmental Parameters 187
- Other Parameters 187
- A-4 PowerScan 188
- Cable Pinouts 189
- USB & USB Keyboard 190
- Wand Emulation 190
- 10 Position RJ 191
- Alpha-Numeric Pad 193
- Default Settings 195
- Interface Default Exceptions 196
- RS-232 Wincor/Nixdorf 197
- Keyboards 198
- Keyboard Function 199
- Key Mappings 199
- E-2 PowerScan 200
- E-4 PowerScan 202
- E-6 PowerScan 204
- E-8 PowerScan 206
- Host Commands 207
- F-2 PowerScan 208
- Sample Symbols 209
- ASCII Chart 211
Produits connexes et manuels pour Lecteurs de codes-barres PSC LINEAR IMAGER 7000
(112 pages)
(48 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.075 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels